Experimental evaluation of hot mix asphalt using coal bottom ash as partial filler replacement

Muhammad Kamran; Muhammad Tariq Khan; Diyar Khan; Mohd Rosli Mohd Hasan; Noman Khan; Mati Ullah

doi:10.7409/rabdim.023.008

Published: 2023-06-30

Vol. 22 No. 2 (2023)

Experimental evaluation of hot mix asphalt using coal bottom ash as partial filler replacement

Muhammad Kamran , Muhammad Tariq Khan , Diyar Khan , Mohd Rosli Mohd Hasan , Noman Khan , Mati Ullah

Section: Articles

https://doi.org/10.7409/rabdim.023.008

Abstract

The purpose of this study is to evaluate the performance of hot mix asphalt (HMA) prepared with coal bottom ash (CBA) as an alternative mineral filler. In this study, the effect of CBA on rutting, stiffness and fatigue resistance was experimentally evaluated. Combinations of conventional filler (stone dust) with different percentages of CBA (at 1.5%, 3%, and 4.5% by volume) were adopted. The HMA samples were prepared and tested using the Marshall mix design method. Following the Asphalt Institute MS-2 and the Pakistani National Highway Authority (NHA) General Specifications, sixty samples of HMA were compacted; stability tests at varying bitumen contents (3.5%, 4.0%, 4.5%, 5.0%, and 5.5%) were used to determine the optimum bitumen content (OBC) in the mixture for each percentage of CBA in the filler. For 0%, 1.5%, 3%, and 4.5% CBA, the optimum bitumen contents of 4.27%, 4.47%, 4.53%, and 5.0% were obtained, respectively. They were used throughout the study. Three samples with the optimum binder content were made for each of the four analysed CBA proportions. The wheel tracker test was run on 12 OBC samples, and the dynamic modulus test was run on 12 OBC samples. The Marshall stability and flow test results showed that the samples prepared with 3% CBA as filler and an OBC of 4.53% satisfied the NHA requirements for flexible pavement. It was noted that CBA greatly improves the rutting resistance and stiffness of asphalt mixtures. It also improved the fatigue life. Therefore, adding up to 3% CBA by volume to stone dust used as filler in asphalt concrete can minimize the need for stone dust and provide a suitable method of CBA disposal.

Keywords:

durability, fatigue life, industrial by-product, Marshall properties, permanent deformation, waste materials.

Similar Articles

Pavel Reiterman, Martin Keppert, Effect of various de-icers containing chloride ions on scaling resistance and chloride penetration depth of highway concrete , Roads and Bridges - Drogi i Mosty: Vol. 19 No. 1 (2020)
Janusz Rymsza, Method of determination of the service load capacity of existing railway bridges and viaduct called “RYM-SZYNA” , Roads and Bridges - Drogi i Mosty: Vol. 23 No. 1 (2024)
Jacek Gołaszewski, Aleksandra Kostrzanowska, Patrycja Miera, Michał Drewniok, Grzegorz Cygan, Joanna Deszcz, Admixtures effectiveness in mortars in the presence of calcareous fly ash , Roads and Bridges - Drogi i Mosty: Vol. 12 No. 2 (2013)
Bartłomiej Krawczyk, Piotr Mackiewicz, Antoni Szydło, Influence analysis of counterweight type used in static plate test on identified parameters of pavement courses and subgrade , Roads and Bridges - Drogi i Mosty: Vol. 14 No. 2 (2015)
Urszula Kołodziejczyk, Michał Ćwiąkała, Analysis of the results of model investigation of water capillary rise in road embankments , Roads and Bridges - Drogi i Mosty: Vol. 8 No. 4 (2009)
Stefan Firlej, Jerzy Kukiełka, Load bearing capacity of a national road with base course made of mineral-cement-emulsion mixture after 12 years of exploitation , Roads and Bridges - Drogi i Mosty: Vol. 18 No. 3 (2019)
Marcin Bilski, Marta Mielczarek, Przemysław Górnaś, Mieczysław Słowik, Patrycja Wojciechowska, The effect of the mixing method of the addition of Gilsonite natural bitumen on asphalt mixture properties , Roads and Bridges - Drogi i Mosty: Vol. 21 No. 3 (2022)
Zdzisława Owsiak, Przemysław Czapik, Justyna Zapała-Sławeta, Testing the cement, hydrated lime and cement by-pass dust mixtures hydration , Roads and Bridges - Drogi i Mosty: Vol. 19 No. 2 (2020)
Michał Pawłowski, Alternative structures of railroad subgrade protective layers , Roads and Bridges - Drogi i Mosty: Vol. 22 No. 4 (2023)
Maria Marks, Application of machine learning to determine properties of concretes modified with addition of coal ash , Roads and Bridges - Drogi i Mosty: Vol. 9 No. 3 (2010)

<< < 10 11 12 13 14 15 16 17 18 19 > >>

You may also start an advanced similarity search for this article.

Download files

PDF

Citation rules

Kamran, M., Khan, M. T., Khan, D., Hasan, M. R. M., Khan, N., & Ullah, M. (2023). Experimental evaluation of hot mix asphalt using coal bottom ash as partial filler replacement. Roads and Bridges - Drogi I Mosty, 22(2), 167–179. https://doi.org/10.7409/rabdim.023.008

Cited by / Share

References

Joshi R.C., Lohita R.P.: Fly Ash in Concrete: Production, Properties and Uses. Gordon and Breach, Amsterdam, 1997
Google Scholar

Wang N., Sun X., Zhao Q., Yang Y., Wang P.: Leachability and adverse effects of coal fly ash: A review. Journal of Hazardous Materials, 396, 2020, ID article: 122725, DOI: 10.1016/J.JHAZMAT.2020.122725
Google Scholar

Ahmaruzzaman M.: A review on the utilization of fly ash. Progress in Energy and Combustion Science, 36, 3, 2010, 327-363, DOI: 10.1016/J.PECS.2009.11.003
Google Scholar

Lior N.: Sustainable energy development: The present (2009) situation and possible paths to the future. Energy, 35, 10, 2010, 3976-3994, DOI: 10.1016/J.ENERGY.2010.03.034
Google Scholar

Yao Z.T., Ji X.S., Sarker P.K., Tang J.H., Ge L.Q., Xia M.S., Xi Y.Q.: A comprehensive review on the applications of coal fly ash. Earth-Science Reviews, 141, 2015, 105-121, DOI: 10.1016/J.EARSCIREV.2014.11.016
Google Scholar

Rafieizonooz M., Mirza J., Salim M.R., Hussin M.W., Khankhaje E.: Investigation of coal bottom ash and fly ash in concrete as replacement for sand and cement. Construction and Building Materials, 116, 2016, 15-24, DOI: 10.1016/J.CONBUILDMAT.2016.04.080
Google Scholar

Abubakar A.U., Baharudin K.S.: Tanjung Bin Coal Bottom Ash: From Waste to Concrete Material. Advanced Materials Research, 705, 2013, 163-168, DOI: 10.4028/WWW.SCIENTIFIC.NET/AMR.705.163
Google Scholar

Muthusamy K., Rasid M.H., Jokhio G.A., Mokhtar Albshir Budiea A., Hussin M.W., Mirza J.: Coal bottom ash as sand replacement in concrete: A review. Construction and Building Materials, 236, 2020, ID article: 117507, DOI: 10.1016/J.CONBUILDMAT.2019.117507
Google Scholar

Rostami R., Klemm A.J.: Influence of superabsorbent polymers on properties of fiber reinforced mortars containing fly ashes. Roads and Bridges - Drogi i Mosty, 19, 2, 2020, 149-163, DOI: 10.7409/rabdim.020.010
Google Scholar

Singh N., Shehnazdeep Bhardwaj A.: Reviewing the role of coal bottom ash as an alternative of cement. Construction and Building Materials, 233, 2020, ID article: 117276, DOI: 10.1016/j.conbuildmat.2019.117276
Google Scholar

Raza M.A., Khatri K.L., Memon M.A., Rafique K., Haque M.I.U., Mirjat N.H.: Exploitation of Thar coal field for power generation in Pakistan: A way forward to sustainable energy future. Energy Exploration & Exploitation, 40, 4, 2022, 1173-1196, DOI: 10.1177/01445987221082190
Google Scholar

Pakistan’s Thar Coal Power Generation Potential, Private Power & Infrastructure Board. NEPRA, Pakistan, 2008
Google Scholar

Argiz C., Sanjuán M.Á., Menéndez E.: Coal Bottom Ash for Portland Cement Production. Advances in Materials Science and Engineering, 2017, 2017, ID article: 6068286, DOI: 10.1155/2017/6068286
Google Scholar

Chuanfeng Z., Yupeng F., Zhuang M., Xue Y.: Influence of mineral filler on the low-temperature cohesive strength of asphalt mortar. Cold Regions Science and Technology, 133, 2017, 1-6, DOI: 10.1016/J.COLDREGIONS.2016.10.006
Google Scholar

Cheng Y., Tao J., Jiao Y., Tan G., Guo Q., Wang S., Ni P.: Influence of the properties of filler on high and medium temperature performances of asphalt mastic. Construction and Building Materials, 118, 2016, 268-275, DOI: 10.1016/J.CONBUILDMAT.2016.05.041
Google Scholar

Ramzi N.I.R., Shahidan S., Maarof M.Z., Ali N.: Physical and Chemical Properties of Coal Bottom Ash (CBA) from Tanjung Bin Power Plant. IOP Conference Series: Materials Science and Engineering, 160, 1, 2016, ID article: 012056, DOI: 10.1088/1757-899X/160/1/012056
Google Scholar

Tenza-Abril A., Saval J., Cuenca A.: Using sewage-sludge ash as filler in bituminous mixes. Journal of Materials in Civil Engineering, 27, 4, 2015, DOI: 10.1061/(ASCE)MT.1943-5533.0001087
Google Scholar

Bajare D., Bumanis G., Upeniece L.: Coal combustion bottom ash as microfiller with pozzolanic properties for traditional concrete. Procedia Engineering, 57, 2013, 149-158, DOI: 10.1016/j.proeng.2013.04.022
Google Scholar

Singh M., Siddique R.: Effect of coal bottom ash as partial replacement of sand on properties of concrete. Resources, Conservation and Recycling, 72, 2013, 20-32, DOI: 10.1016/J.RESCONREC.2012.12.006
Google Scholar

Muniandy R., Aburkaba E.E.: The effect of type and particle size of industrial wastes filler on indirect tensile stiffness and fatigue performance of stone mastic asphalt mixtures. Australian Journal of Basic and Applied Sciences, 5, 11, 2011, 297-308
Google Scholar

Zulkati A., Diew W.Y., Delai D.S.: Effects of fillers on properties of asphalt-concrete mixture. Journal of Transportation Engineering, 138, 7, 2012, 902-910, DOI: 10.1061/(ASCE)TE.1943-5436.0000395
Google Scholar

Ghaffar A., Siddiqi Z.A., Ahmed K.: Assessing Suitability of Margalla Crush for Ultra High Strength Concrete. Pakistan Journal of Engineering and Applied Sciences, 7, 2010, 38-46
Google Scholar

El Moudni El Alami S., Moussaoui R., Monkade M., Lahlou K., Hasheminejad N., Margaritis A., Van den Bergh W., Vuye C.: Lime Treatment of Coal Bottom Ash for Use in Road Pavements: Application to El Jadida Zone in Morocco. Materials, 12, 17, 2019, 2674, DOI: 10.3390/ma12172674
Google Scholar

Lokeshappa B., Dikshit A.K.: Behaviour of Metals in Coal Fly Ash Ponds. APCBEE Procedia, 1, 2012, 34-39, DOI: 10.1016/j.apcbee.2012.03.007
Google Scholar

Baite E., Messan A., Hannawi K., Tsobnang F., Prince W.: Physical and transfer properties of mortar containing coal bottom ash aggregates from Tefereyre (Niger). Construction and Building Materials, 125, 2016, 919-926, DOI: 10.1016/j.conbuildmat.2016.08.117
Google Scholar

Jarusiripot C.: Removal of reactive dye by adsorption over chemical pretreatment coal based bottom ash. Procedia Chemistry, 9, 2014, 121-130, DOI: 10.1016/j.proche.2014.05.015
Google Scholar

Rathnayake M., Julnipitawong P., Tangtermsirikul S., Toochinda P.: Utilization of coal fly ash and bottom ash as solid sorbents for sulfur dioxide reduction from coal fired power plant: Life cycle assessment and applications. Journal of Cleaner Production, 202, 2018, 934-945, DOI: 10.1016/j.jclepro.2018.08.204
Google Scholar

Colonna P., Berloco N., Ranieri V., Shuler S.T.: Application of Bottom Ash for Pavement Binder Course. Procedia - Social and Behavioral Sciences, 53, 2012, 961-971, DOI: 10.1016/j.sbspro.2012.09.945
Google Scholar

Khitab A., Bukhari S., Tayyab S.: Effect of Partial Replacement of Sand by Coal Bottom Ash in Concrete. Southern Journal of Research, 2, 2, 2022, 102-106, DOI: 10.20021/sjr.v2i2.56
Google Scholar

MS-2 Asphalt Mix Design Methods. Asphalt Institute, Pakistan, 2014
Google Scholar

AASHTO T 245 Standard Method of Test for Resistance to Plastic Flow of Asphalt Mixtures Using Marshall Apparatus. American Association of State Highway and Transportation Officials (AASHTO), Washington, 2022
Google Scholar

NHA General Specification. National Highway Authority (NHA), Government of Pakistan, 1998
Google Scholar

Luo H., Chen S., Lin D.F., Cai X.: Use of incinerator bottom ash in open-graded asphalt concrete. Construction and Building Materials, 149, 2017, 497-506, DOI: 10.1016/j.conbuildmat.2017.05.164
Google Scholar

ASTM D6927 Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures. American Society of Testing and Materials (ASTM), Washington, 2015
Google Scholar

Ameli A., Babagoli R., Norouzi N., Jalali F., Poorheydari Mamaghani F.: Laboratory evaluation of the effect of coal waste ash (CWA) and rice husk ash (RHA) on performance of asphalt mastics and Stone matrix asphalt (SMA) mixture. Construction and Building Materials, 236, 2020, ID article: 117557, DOI: 10.1016/j.conbuildmat.2019.117557
Google Scholar

AASHTO T 324 Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures. American Association of State Highway and Transportation Officials (AASHTO), Washington, 2019
Google Scholar

AASHTO T 342 Standard Method of Test for Determining Dynamic Modulus of Hot Mix Asphalt (HMA). American Association of State Highway and Transportation Officials (AASHTO), Washington, 2019
Google Scholar

Tang F., Ma T., Zhang J., Guan Y., Chen L.: Integrating three-dimensional road design and pavement structure analysis based on BIM. Automation in construction, 113, 2020, ID article: 103152, DOI: 10.1016/J.AUTCON.2020.103152
Google Scholar

Yang J., Li Z., Xu X.: Preparation and evaluation of cooling asphalt concrete modified with SBS and tourmaline anion powder. Journal of Cleaner Production, 289, 2021, ID article: 125135, DOI: 10.1016/j.jclepro.2020.125135
Google Scholar

Zhang W., Shen S., Faheem A., Basak P., Wu S., Muhammad L.: Predictive quality of the pavement ME design program for field performance of warm mix asphalt pavements. Construction and Building Materials, 131, 2017, 400-410, DOI: 10.1016/j.conbuildmat.2016.11.086
Google Scholar

AASHTO T321 Standard Method of Test for Determining the Fatigue Life of Compacted Hot-Mix Asphalt (HMA) Subjected to Repeated Flexural Bending. American Association of State Highway and Transportation Officials (AASHTO), Washington, 2007
Google Scholar

Shen S., Zhang W., Shen L., Huang H.: A statistical based framework for predicting field cracking performance of asphalt pavements: Application to top-down cracking prediction. Construction and Building Materials, 116, 2016, 226-234, DOI: 10.1016/j.conbuildmat.2016.04.148
Google Scholar

Shen S., Zhang W., Wang H., Huang H.: Numerical evaluation of surface-initiated cracking in flexible pavement overlays with field observations. Road Materials and Pavement Design, 18, 1, 2017, 221-234, DOI: 10.1080/14680629.2016.1138879
Google Scholar

Muhammad Kamran

Affiliation:

University of Engineering and Technology, Department of Civil Engineering, Peshawar, Pakistan

Muhammad Tariq Khan

Affiliation:

University of Engineering and Technology, Department of Civil Engineering, Peshawar, Pakistan

Diyar Khan

diyarkhan1000@gmail.com

Affiliation:

Politechnika Śląska, Wydział Transportu i Inżynierii Lotniczej, Studia doktoranckie, ul. Krasińskiego 8., 40-019 Katowice

Bio Statement (e.g., department and rank)

Silesian University of Technology, Faculty of Transport and Aviation Engineering, Department of Road Transport, 8 Krasińskiego St., 40-019 Katowice

Mohd Rosli Mohd Hasan

Affiliation:

University Sains Malaysia (Engineering Campus), School of Civil Engineering,.14300 Nibong Tebal, Penang, Malezja

Noman Khan

Affiliation:

Sarhad University of Science and Information Technology Ring Road Campus, Department of Civil Engineering, Peshawar, KPK, Pakistan

Mati Ullah

Affiliation:

University of Engineering and Technology, Department of Civil Engineering, Taxila, Punjab, Pakistan

Experimental evaluation of hot mix asphalt using coal bottom ash as partial filler replacement

Abstract

Keywords:

Similar Articles

Downloads

Muhammad Kamran

Muhammad Tariq Khan

Diyar Khan

Mohd Rosli Mohd Hasan

Noman Khan

Mati Ullah